06-08-2017 07:25 PM
Hello,
I've provisioned a few servers with a bunch of Intel S3610's and I'm a bit concerned about the "Raw Read Error Rate" values. The tools shows all drives as healthy and there are no other errors as shown as full SMART data pasted below for one drive.
Does these values mean anything?
Thanks
:~# isdct show -smart 01 -intelssd
- SMART Attributes BTHXXXXXXXX800NGN -
- 01 -
Action : Pass
Description : Raw Read Error Rate
ID : 01
Normalized : 130
Raw : 3163710634
Status : 14
Threshold : 39
Worst : 130
- SMART Attributes BTHXXXXXXXX800NGN -
- 01 -
Action : Pass
Description : Raw Read Error Rate
ID : 01
Normalized : 130
Raw : 3158519941
Status : 14
Threshold : 39
Worst : 130
- SMART Attributes BTHXXXXXXXX800NGN -
- 01 -
Action : Pass
Description : Raw Read Error Rate
ID : 01
Normalized : 130
Raw : 3164737702
Status : 14
Threshold : 39
Worst : 130
- SMART Attributes BTHXXXXXXXX800NGN -
- 01 -
Action : Pass
Description : Raw Read Error Rate
ID : 01
Normalized : 130
Raw : 3152729088
Status : 14
Threshold : 39
Worst : 130
- SMART Attributes BTHXXXXXXXX800NGN -
- 01 -
Action : Pass
Description : Raw Read Error Rate
ID : 01
Normalized : 130
Raw : 3161462193
Status : 14
Threshold : 39
Worst : 130
- SMART Attributes BTHXXXXXXXX800NGN -
- 01 -
Action : Pass
Description : Raw Read Error Rate
ID : 01
Normalized : 130
Raw : 3155225677
Status : 14
Threshold : 39
Worst : 130
- SMART Attributes BTHXXXXXXXX800NGN -
- 01 -
Action : Pass
Description : Raw Read Error Rate
ID : 01
Normalized : 130
Raw : 3159076215
Status : 14
Threshold : 39
Worst : 130
- SMART Attributes BTHXXXXXXXX800NGN -
- 01 -
Action : Pass
Description : Raw Read Error Rate
ID : 01
Normalized : 130
Raw : 3156418161
Status : 14
Threshold : 39
Worst : 130
"SMART Attributes BTHXXXXXXXX800NGN":
{
"01":
{
"Action":"Pass",
"Description":"Raw Read Error Rate",
"ID":"01",
"Normalized":130,
"Raw":1925235567,
"Status":14,
"Threshold":39,
"Worst":130
},
"05":
{
"Action":"Pass",
"Description":"Re-allocated Sector Count",
"ID":"05",
"Normalized":100,
"Raw":0,
"Status":51,
"Threshold":1,
"Worst":100
},
"09":
{
"Action":"Pass",
"Description":"Power-On Hours Count",
"ID":"09",
"Normalized":100,
"Raw":353,
"Status":50,
"Threshold":0,
"Worst":100
},
"0C":
{
"Action":"Pass",
"Description":"Power Cycle Count",
"ID":"0C",
"Normalized":100,
"Raw":30,
"Status":50,
"Threshold":0,
"Worst":100
},
"0D":
{
"Action":"Pass",
"Description":"ECC Rate",
"ID":"0D",
"Normalized":119,
"Raw":719184773999,
"Status":30,
"Threshold":0,
"Worst":100
},
"B3":
{
"Action":"Pass",
"Description":"Used reserved block count (total)",
"ID":"B3",
"Normalized":100,
"Raw":0,
"Status":51,
"Threshold":10,
"Worst":100
},
"B4":
{
"Action":"Pass",
"Description":"Unused Reserved block count (total)",
"ID":"B4",
"Normalized":100,
"Raw":17930,
"Status":50,
"Threshold":0,
"Worst":100
},
"B5":
{
"Action":"Pass",
"Description":"Program fail count (total)",
"ID":"B5",
"Normalized":100,
"...
06-09-2017 02:57 PM
Hello Ispirto,
We were checking with a different data center drive here and we did not have that specific SMART attribute.We'll be working on this specifically and we will try to replicate with the same drive you have, please expect an update next week.We do agree with you that the values show really nice, so it may not be something to worry about.Regards,Nestor C06-16-2017 03:00 PM
Hello Ispirto,
Could you please share a screenshot of your SSD's label?Also, do you have the SSD connected to a RAID controller card or directly to the motherboard?Please share with us the dump log, you can use this command: Isdct dump –intelssd Regards,Nestor C06-23-2017 02:43 PM
Hello Ispirto,
We'd like to know if you were able to read our previous post and follow the instructions above? We'll be waiting for your response.Regards,Nestor C